English
This simple trick can give a nice lacquer finish on plywood, and I have already talked about how to paint MDF and get smooth edges. If you build with clear wood, you would probably use edge bands, but I am sure you cannot.
After you cut your plywood parts, the first step is to sand down the sides of the plywood cutting saw and the edges. It is sanded a lot to get the desired shine at the end. Therefore, use an 80% sanding pad while sanding with 120 grit sandpaper.
The wooden panels on the barn door are lined with plywood, so wipe the wood clean with a cloth and dye it to match the rest of the door. I used the side - banded edges and then sanded the iron veneer I tried at the time, and then bleached it.
Once you have applied the edge banding, give it a good sanding until it is smooth and smooth enough to get edge treatment with the best abrasive.
Once you have removed the edge banding, you can smooth out any uneven areas on the edges of the material with sandpaper or a sanding block. You can also remove the old edges by applying heat with an iron and running a spatula knife over them to lift them off the materials. A heat-active adhesive is placed on the back of your veneer, which adheres to a flat surface.
If you want a refined look, there are three main ways to enhance your plywood edges. Plywood is flaky at the cut edges, so it grinds round like Blaine for the upcoming creative project Helps to ensure a clean, finished edge. After cleaning the edges and applying a new edge tape, follow the steps above to give your project a new coat of paint. The open edges of the plywood make for a really fun style, and if you want more of a finished look, this is one of the best options.
Solid wooden edges not only give you a beautiful, finished look but also allow you to mill and shape the edges to obtain a high-quality, tailored look.
If you still paint the piece, fill the cavities at the edges with putty (like grout) before you finish with this method. Remember that the wood filler you use will shrink when it dries out.
In this case, you should sand each layer with 120-grit sandpaper before applying the second layer on a smooth, even surface. Make sure you sand and fill the ends of the board, as most plywood has cavities and boards will often be rough.
This also allows you to fill the ends of the grain to create a smooth surface for painting, as well as for other purposes such as painting.
Before starting, it is necessary to get to room temperature (65-75 ° F) and sand the front of the billboard with fine sandpaper to smooth any unevenness or increased wood grain in the plywood. Apply an oil-based primer over the entire plywood edge with a 2.5 mm sander.
When sanding plywood, it is important to treat the surface with a veneered layer and to avoid the sander falling off. Now apply the first layer of black enamel to the sanded surface with a roller and a low nap.
In this case, I tried to paint the edge of the sand and fill in the color that connects to the face veneer. Brush the edges by hand and sanding your work, adjust the machine and pass the 120 - 150 grains of sandpaper. You can sand the surface, but with your machine, you smooth the grain and then brush again, by hand.
For example, from 180 - 220 to the last grinding with a 180 / 220 and then again to 220. When applying a stain, it is a good policy to grind the snippets, but not too much, just enough.
When sanding on a flat surface, use the flat block to secure the sandpaper and advance to the next finer sandpaper. The most efficient way is to use a finer grit, which can be used to sand for a little longer. Remove the sanded dust by using the same sandpaper you used in the last machine sanding or by using one of the three sanding methods.
Grinding the grains often removes them from the herd faster than the grain passes through, but not as fast as the other two methods.
It is tempting to take a piece of sandpaper and sand it off without using a support block, but if you get into a situation where you cannot avoid sanding the grains at the joint where the two parts meet at a right angle, you should try using a back block with a solid surface, such as a plywood board or a wooden board.
