English
You can change the look of the plywood by making it look as if you have used hardwood by applying a coating of wood stain to the floor to achieve the final finish. You can get the plywood grain out further, but you have to sweep and wipe to make sure you have a perfectly clean floor to apply the finish too, and you can also change it to make it look like you've used a plywood board.
You can bleach the wooden floorboards to get them sun-kissed, weathered, or dye them to match furniture and cladding. If you decide to discolor your plywood floor, apply a sanding fastener to the surface of each board, which helps to ensure that the stain penetrates evenly. You can apply the stains, rub them off to remove any excess stains, let them dry, and apply another stain.
When you're done, you have a uniquely designed floor to be proud of and a budget that it can afford. Why not try to paint your plywood floor in style, and what budget can you afford?
Make sure your plywood is of high quality and that all major holes, dents, and partitions have been fixed or repaired.
If you don't know how to choose plywood floors, it's worth doing your homework and making sure you don't lay floors that warp and get damaged quickly. Plywood is generally considered the wood of choice for the underfloor and can be used on any floor. It would not hurt to traverse the whole floor before wetting the laminated timber to ensure that nothing can be burned, but it would not hurt.
At this point, you want to sand plywood cutting saw the ground again, even if you have done so before, but the grain must be knocked out to make the ground even and smooth again.
If the raised part is not well supported by the wood down, the spot will break and only you can decide which one is. You can either choose to lift the lower part of the underbody or lower the higher part, but it is generally assumed that there is more.
Note: You can also use a belt sander or floor sander to remove the high surfaces by sanding the underbody yourself. I only used a small palm frond, but of course, a larger soil saver would work much faster. Simply lower with it to the highest point on an underfloor and then remove wood from the floor beams with a plane. Use the belt protector or floor sander and remove the underbody with the tape and sanders.
Just remember that the plywood will not be silky smooth, but it is still a solid piece of wood, just not as smooth as on the floor.
The purpose of sanding is to smooth out larger bumps, and this can be done with a roller or an extension handle. The quickest way to do this is to use wood filler and then cut the edges of the brush. Fill the gaps between plywood and the underbody with a quick-setting dry tree mixture or trowel for a stunning DIY finish.
The sky is the limit when it comes to design, but the key is to prepare as discussed above. While painting plywood floors is covered with a few layers of polyurethane, special details can also be used. Primer ensures that the paint adheres and also helps to seal loose plywood chips.
The moisture from the sealer increases the grain of the wood so that it feels rough again, but not as rough as the original wood.
The sealing is not difficult, but to do that you need to give more stains to the plywood. A good way to test it is to apply it on an additional piece of laminated wood and then apply the stain again to see what the finished result will look like. Although the process may seem laborious when you do the footwork of filling and sanding, the end product actually looks much better.
For example, I moved from 180 - 220 to the last grinding grains and then to 120 - 120. A good policy is to sand with a patch-on varnish before applying the stain, but not afterward.
When sanding on a flat surface, use flat blocks to secure the sandpaper and advance to the next finer grain. Remove all ground dust by using the same sandpaper that you used for the last machine grinders. I used the three-grinding method, but you can use a grit finer if you sand a little longer. For the most efficient method, use one grain or one of the four grits you use in the first step of each of these three grinding methods.
When cutting boards or cutting boards, use a circular saw and reduce the grinding effort. The less sand, the fewer cracks the wood parts have, and the more dust you can reduce in the sandpaper, reducing the number of cracks and thus the cost of the project.
